Was able to use another computer that can access downloads...
This Lil tablet that i post on, is limited.
TECH REPORT - Far more info.
Pages 47 - 48 show a superb picture of the main mimerslization zone.
COMECO - appears they selectively chose certain sections of the cores for assaying.
Hence - it's best to stick to current findings.
Should one dismiss Comeco's assay results ?
No. All because the cherry picked core sections by Comeco, can be still relavant = high gram readings = which can perhaps = boost lower gram readings...Issue ? Those sections of core are gone or been assayed...
What LARA performed to, the cores was exactly what I suggested yesterday.
Reassaying and finding the true gram per tonne.
I think it was a perfect call = LARA takimg the time to do, so.
There's amazing magnetic maps of the entire Preview claims.
Showing resistivites all along the Preview corridor.
My previous beef with ALS, and their colorful depiction of the Preview drill results...
And the point in case = AlS showing different core colors than what the airborne magnetics show..
Can make it confusing. Tech Report keeps the continuity of coloration of airborne surevey and MINERALIZATION zones below the same...very helpful.
OVER THE YEARS
Each of 3 junior drill campaigns has perfored same proceedures.
Same angles, drilling into same deposit, and well...one followed the same routine as the previous.
No, knew logic to = MAKE AN IMPACT ON THE = EPICENTER OF = DEPOSIT.
There has got to be some way...
Of incorporating the LARA historical Comeco core work into a compliant resource.
Even if a good 70% of the inferred resource in conjunction of LARA's findings could be
made compliant and with a result of at least 2 grams...it would move this project forward.
Question is...how can one incorporate the LARA findings ( specifically ) inferred mineral zone ?
Not too sure how Comstock could do this...would it be review the LARA assay's and quarter off
a portion of Comeco drills = specifically = dense area where most of the Comeco drills were punched ?
After seeing the size of the vein below grade = entirely different diagrams with in tech report...
And after my own assessment of...reviewing the 121 - 122 holes with 200 m hits...
And after reading the tech report seeing there's also free gold ( circle charts ) outside of main vein
I still arrive at, my original conclusion...
DEPTH OF VEIN ZONE IS NEEDED.
Aside of incorporating a portion of LARAs findings into a complaint resource.
Depth of MAIN VEIN is needed to take the project to a new level.
It's what ClaudecMimerals did.
Went deep.
It's what SSR, is also now doing...going deep chasing the larger veins.
It's what this region is known for, and so similar to Quebecs greenstone belt.
Though gold is near surface just like historical Quebec regions, one has to ask...
What are the majority of Quebec gold miners now doing ?
CHASING THE FORMER MASSIVE VEINS = EVEN FURTHER DOWN.
If I were, incharge of this project...
Yes...I would have a very hard time pulling away from the " action " of wanting to prove a
Long Strike length...
But...i would then ask,myself...
What's the quickest way to create quality results ?
Lunch more holes trying to lengthen a strike zones?
That would take a few more years.
Or...
Focus on what's been worked on the most ?
THE MAIN MINERALIZATION ZONE.
+ TRY TO MAKE LARAS FINDINFS COMPLIANT
+ ONCE MADE COMPLIANT A PORTION OF INFERRED = BEEFS UP THE INDICATED
+ GO DEEP...DRILL DEEP.
It's long over due...and would tell the real story
It might reveal if the ven system runs as deep as, See Bee's...1200+ meters.
If, Comstock could quadron off an area...
200 meters x 200 meters x 600 meters drill depth.
And prove the vein runs really deep...?
It is on my opinion the quickest way to make an impact.
Meaningful impact.
Reverse drill program
Drill opposite 45 degrees
It would keep inline of massive vein
It would allow, Comstock to drill the depths of the vein
And would define the depth of the vein.
Asxseen in the tech report...
The vein is wide.
Stays wide even at the 200 meter level downhole.
Broad shoulders vein.
And only shows slight signs of shrinkage at 200 meter level.
Could be an easy quantative guess to provide an inferred tonnage
Using a calculation that accounts for vein shrinkage going downhole per meter.
Example = if vein shrinks 2 meters for every 50 meters you down
One could Guage ( round about ) how wide the vein could be @ 600 meter level
IRONICALLY....
Most all the focus, has been placed on drilling towards PAP Lake.
There is anorher diorite gabbro rock zone opposite side to the main south preview hub.
Whereas...it's virgin territory.
Same rock disposition as what south preview has...yet...untouched.
What if there is another parallel vein similar to south Previews PaP Lake
On the other side of the yellow volcanic + sediment separation zone going towards contact lake ?
Oh hello...it's all Diorite on upper left side of map below.
Much easier to mine with shaft = south preview and if the opposite side had another similar vein..
Simply make an underground access to opposite side...keeping project centralized = Main Hub
VERUS...entire strike length = all of 3 preview claims.
MAP -
https://s.yimg.com/ny/api/res/1.2/RLo_ZuOxadEPPMNWyPMFTQ--~A/YXBwaWQ9aGlnaGxhbmRlcjtzbT0xO3c9ODAwO2lsPXBsYW5l/https://globalfinance.zenfs.com/images/CA_AFTP_MarketWire_XHTML/PSW-Drillhole-location-map-Feb-20131_original.jpg
WHAT IF ...?
What if Comstock focused on the Main Vein ?
What if the main broad vein zone could be compounded on ?
What if...200 m wide x 200 m long and what if Comstock drilled an opposite 45 degree angle
to drill directly into the massive vein and Chase it down ...?
Would tapping a few more sporadic holes North Preview make excitement ?
Or...
Chasing the Massive Vein all the way down...?
Comstock presses News - Chasing Massive Vein -
At 250 meter = updates shareholders
At 300 meter = updates shareholders
At 350 meter = updates shareholders
At 600 meter = updates shareholders
What if this vein is similar to See Bee's ( STEEPY dipping vein ? )
Oh hello....!
200 m x 200 m x 600 m depth ? ( exmaple )
24,000,000 tonnes
@ 2 grams ( example )
48,000,000 grams
÷ 31.1 ( ounce conversion )
= 1.5 million ounces...
This mentality of junior punching random holes all over property...
Doesn't quite add up the ounces....takes years....and well...eventually the project
is passed onto another junior....ring a bell ?
Again...
It is my BELEIF ....
= Incorporating a portion of LARA's assaying into complaint resource = a must do.
= Quadron off the thickest mass of mimerslization zone + work with LARA's findings in this zone
= Drill deep...
= Let shareholders or investors know the depths of this massive vein.
= If it's still apparent at 600 m depth....let the drills keep turnimg...
= That's how you keep investor interest.
Just my own opinion...
Not investment advice.
Happy i was able to review the tech report.
Lot's of good info...and good maps and charts.
Wango~