TORONTO, ONTARIO--(Marketwired - Mar 20, 2017) - Plateau Uranium Inc. ("Plateau Uranium" or the
"Company") (TSX VENTURE:PLU)(FRANKFURT:QG1) is pleased to announce strong initial drill results from the
high-grade Pinocho Target at the Company's Macusani Plateau Project in southeastern Peru. Initial results from six (6) diamond
drill holes drilled on two (2) platforms are reported from Pinocho, which represents one of the most prospective of several
previously untested higher grade, near-surface uranium targets on the Company's extensive 910 km2 land package.
Historical underground adits were established previously at Pinocho by IPEN ("Institute of Peruvian Nuclear
Energy") (see Company news release dated November 28, 2016 for full description of Pinocho target). Drilling at Pinocho
continues along a 1.4 km trend.
Initial Pinocho Drilling Highlights
- Two drill holes from Platform 1, returned in excess of 2,000 ppm U (2,350 ppm U3O8) over 2 and 3
metres, repectively, within broader intervals of uranium mineralization ranging between 500-800 ppm U (590-940 ppm
U3O8) over 8-9 metres, which is 2-3 times higher than the ~288 ppm U3O8 average
life-of-mine uranium grade reported in the Company's 2016 Preliminary Economic Assessment ("PEA") (see Company
news release dated January 10, 2016).
- Best uranium intersections are at potentially open pittable depths, within 50 metres of surface.
- Uranium mineralization is located within broader zones of lithium mineralization ranging from 12-37 metres thick, with
consistent grades similar to the existing reported lithium resources at Macusani (550-700 ppm Li; 0.12-0.15%
Li2O).
- Pinocho represents a potential higher grade starter resource area, which may serve to improve uranium project economics in
early years of operation.
- Sensitivity analysis from the financial model reported in the Company's PEA base case for uranium only, dated January 12,
2016, highlights a post-tax NPV8 of $360 million and an IRR of 29.2% with a payback period of 2.5 years using a
$40/lb U3O8 selling price, exclusive of any Lithium co-product potential. The average life-of-mine head
grade included in the PEA was 288 ppm U3O8, significantly lower in grade than the current drill results
presented in today's release.
- Company-owned diamond drill rigs continue drilling along a 1.4 km long trend at Pinocho, aimed at further defining resource
potential in the area.
Pinocho Target Highlights
- Underground adits at Pinocho were developed by IPEN along high grade, sub-horizontal, planar zones of uranium
mineralization with thicknesses exceeding 2 metres, surrounded by lower grade disseminated mineralization of unknown thickness
and scale; this mineralization remains open in all directions.
- 96 channel samples collected from the Pinocho adits in 2009 by the Company intersected uranium grades up to 4.37% U (5.15%
U3O8) averaging over 3,000 ppm U within a background of 15 ppm U.
- 12 chip samples collected from the Pinocho adits contained >1% U (1.18% U3O8), and 50 samples
contained >500 ppm U (590 ppm U3O8)
Ted O'Connor, CEO of Plateau Uranium, commented: "We are extremely pleased with these results from initial
drilling at Pinocho. We have successfully located an extension of the known uranium and lithium resources to the southeast of the
Kihitian Complex, and look forward to completing additional drilling to define the resource potential of this area. The higher
grade uranium mineralization and consistent lithium grades we are intersecting at Pinocho, combined with the potential for
enhanced uranium and lithium by-product recoveries announced in our previous news release, should serve to further enhance the
already robust, low cost, project economics of our Macusani Project."
Pinocho Drilling Details
Analytical results have been received from the first 6 diamond drill holes from 2 platforms testing the Pinocho target.
Typically, each platform can have up to 5 drill holes collared from the same location, depending on topography. Each individual
platform usually consists of a vertical drill hole and 4 inclined drill holes drilled in opposing directions (NE, NW, SE & SW) at
inclinations of between -45° to -70° from horizontal. All holes are drilled using large diameter HQ core.
All drill holes have intersected the upper mineralized horizon (Manto A) within 50 metres of surface, with variable uranium
content as outlined in Table 1 below. Consistent lithium grades have also been intersected within the individual lava flow
units.
Table 1 - Pinocho Drill Hole Results - Uranium and Lithium Intersections
|
URANIUM |
LITHIUM |
PT-PCH1-TNE - 203.0 m depth -70° inclination @ 065° Az |
From |
To |
Thickness (m) |
Grade (ppm U) |
Grade U3O8 (lbs/ton) |
From |
To |
Thickness (m) |
Grade Li (ppm) |
Grade Li2O (ppm) |
|
53.0 |
61.0 |
8.0 |
861 |
2.031 |
50.0 |
70.0 |
20.0 |
535 |
1,154 |
including |
53.0 |
56.0 |
3.0 |
2,160 |
5.094 |
|
|
|
|
|
|
66.5 |
70.0 |
3.5 |
162 |
0.382 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
URANIUM |
LITHIUM |
PT-PCH1-TNW - 219.2 m depth -70° inclination @355° Az |
From |
To |
Thickness (m) |
Grade (ppm U) |
Grade U3O8 (lbs/ton) |
From |
To |
Thickness (m) |
Grade Li (ppm) |
Grade Li2O (ppm) |
|
53.0 |
62.0 |
9.0 |
566 |
1.335 |
50.0 |
62.0 |
12.0 |
546 |
1,177 |
including |
53.0 |
55.0 |
2.0 |
2,182 |
5.146 |
160.0 |
180.0 |
20.0 |
584 |
1,259 |
|
88.0 |
96.0 |
8.0 |
148 |
0.349 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
URANIUM |
LITHIUM |
PT-PCH3-TV - 206.0 m depth (vertical) |
From |
To |
Thickness (m) |
Grade (ppm U) |
Grade U3O8 (lbs/ton) |
From |
To |
Thickness (m) |
Grade Li (ppm) |
Grade Li2O (ppm) |
|
50.0 |
68.0 |
18.0 |
142 |
0.335 |
30.0 |
67.0 |
37.0 |
554 |
1,195 |
including |
50.0 |
53.0 |
3.0 |
538 |
1.269 |
155.0 |
160.0 |
5.0 |
828 |
1,785 |
|
121.0 |
96.0 |
8.0 |
51 |
0.12 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
URANIUM |
LITHIUM |
PT-PCH3-TNW - 130.5 m depth -60° inclination @315° Az |
From |
To |
Thickness (m) |
Grade (ppm U) |
Grade U3O8 (lbs/ton) |
From |
To |
Thickness (m) |
Grade Li (ppm) |
Grade Li2O (ppm) |
|
56.5 |
59.0 |
2.5 |
203 |
0.479 |
39.0 |
65.0 |
26.0 |
712 |
1,535 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
URANIUM |
LITHIUM |
PT-PCH3-TSE - 210.4 m depth -55° inclination @135° Az |
From |
To |
Thickness (m) |
Grade (ppm U) |
Grade U3O8 (lbs/ton) |
From |
To |
Thickness (m) |
Grade Li (ppm) |
Grade Li2O (ppm) |
|
61.0 |
66.0 |
5.0 |
107 |
0.252 |
55.0 |
70.0 |
15.0 |
584 |
1,259 |
including |
65.0 |
66.0 |
1.0 |
450 |
1.061 |
175.0 |
190.0 |
15.0 |
868 |
1,872 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
URANIUM |
LITHIUM |
PT-PCH3-TNE - 186.0 m depth -55° inclination @045° Az |
From |
To |
Thickness (m) |
Grade (ppm U) |
Grade U3O8 (lbs/ton) |
From |
To |
Thickness (m) |
Grade Li (ppm) |
Grade Li2O (ppm) |
|
78.0 |
82.0 |
4.0 |
99 |
0.233 |
50.0 |
65.0 |
15.0 |
594 |
1281 |
|
|
|
|
|
|
75.0 |
86.0 |
11.0 |
535 |
1154 |
The deeper uranium mineralized horizon (Manto B) has not been intersected in the currently reported drill holes. Manto B was
expected to be located at approximately 150 metres depth below surface based on projections from the known mineralization at the
Kihitian Complex deposits located to the northwest, but appears to have been flushed away in this area by variations in the local
water table and the presence of rivers at this elevation in this topographical depression (click here to view Figure 1 - Example Map & Cross Section Kihitian
deposit to Pinocho Platform 1).
As observed in Table 1, several higher grade lithium intervals of >800 ppm Li over wide intervals (5-15 metres) have been
intersected in the lower volcanic flow unit where the lower Manto B should have been located. Manto B level mineralization has
been observed in more recently completed drill holes, however, chemical analyses remain outstanding and will be reported as
results become available.
Pinocho Target & Drill Program
Pinocho is located 2 km southeast of the Kihitian deposit, and is believed to be a possible extension of the same
mineralization comprising the Kihitian Complex deposits. Approximately 194 metres (length) of adit development was established at
Pinocho by IPEN in the early 1980's. Adit development followed a high grade core of sub-horizontal uranium mineralization within
a thicker disseminated uranium mineralized envelope. The exposed mineralization within the adits is open in all directions.
Drilling from a total of eight (8) platforms is planned to be completed during this initial Pinocho drill program. Drilling
should be completed in April 2017.
Macusani Uranium-Lithium Deposits
The Macusani Plateau uranium district hosts unique, low temperature supergene-surficial uranium deposits formed in
peraluminous, alkaline volcanic rhyolite host rocks that are approximately 7 million years old. The host rhyolites are inherently
enriched in U, Li, K Al and SiO2, as well as other Large-Ion Lithophile Elements (LILE - Cs, Rb, etc). The uranium
mineralization is less than 1 million years old, as young as ~40,000 years old and comprised primarily of the hexavalent uranium
mineral meta-autunite, and is totally unrelated to volcanic processes. The uranium was scavenged from the host rhyolites by
melting glacial waters circulating through the porous rhyolites well after eruption and cooling, with uranium precipitation due
to evaporation, water table fluctuation, changes in fluid flux and mixing with resident groundwater of subtly different
chemistry. The low-temperatures and benign conditions of uranium deposit formation translates into uranium mineralization that is
easily leached with weak sulphuric acid and represents one of the lowest potential production cost opportunities globally.
The lithium enrichment is widespread and related to the original chemistry of the host rhyolites. Lithium and other LILE
metals were not mobilized during the uranium mobilization-deposition. Lithium is enriched in volcanic glass phases and biotite
and is easily leached with warm sulphuric acid. The potential of producing lithium as a co-product of uranium production is
beginning to be understood, but indications are that lithium co-production represents an excellent opportunity to add value to
the Company's robust uranium projects.
Quality Assurance & Quality Control
Drill core samples are cut longitudinally with a diamond saw with one-half of the core placed in sealed bags and shipped to
Certimin's sample analytical laboratory in Lima for sample preparation, processing and ICP-MS/OES multi-element analysis.
Certimin is an ISO 9000 certified assay laboratory. The program is designed to include a comprehensive analytical quality
assurance and control routine comprising the systematic use of Company inserted standards, blanks and field duplicate samples and
internal laboratory standards.
Qualified Persons
Mr. Ted O'Connor, P.Geo., CEO and a Director of Plateau Uranium and a qualified person as defined by National Instrument
43-101 Standards of Disclosure for Mineral Projects, has reviewed and approved the scientific and technical information contained
in this news release.
About Plateau Uranium
Plateau Uranium Inc. is a Canadian uranium exploration and development company focused on its properties on the Macusani
Plateau in southeastern Peru. The Company controls all reported uranium resources known in Peru, significant and growing lithium
resources and mineral concessions covering over 91,000 hectares (910 km2) situated near significant infrastructure.
Plateau Uranium is listed on the TSX Venture Exchange under the symbol 'PLU' and the Frankfurt Exchange under the symbol 'QG1'.
The Company has 58,043,354 shares issued and outstanding.
Forward Looking Information
This news release includes certain forward-looking statements concerning possible expected results of exploration and
future exploration activities. Forward-looking statements are frequently identified by such words as "may", "will", "plan",
"expect", "anticipate", "estimate", "intend" and similar words referring to future events and results. Forward-looking statements
are based on the current opinions and expectations of management. All forward-looking information is inherently uncertain and
subject to a variety of assumptions, risks and uncertainties, including risks and uncertainties relating to the
interpretation of drill results, the geology, grade and continuity of mineral deposits; the possibility that any future
exploration, development or mining results will not be consistent with our expectations; mining and development risks, including
risks related to accidents, equipment breakdowns, labour disputes (including work stoppages and strikes) or other unanticipated
difficulties with or interruptions in exploration and development; the potential for delays in exploration or development
activities; risks related to commodity price and foreign exchange rate fluctuations; risks related to foreign operations; the
cyclical nature of the industry in which we operate; risks related to failure to obtain adequate financing on a timely basis and
on acceptable terms or delays in obtaining governmental approvals; risks related to environmental regulation and liability;
political and regulatory risks associated with mining and exploration; risks related to the certainty of title to our properties;
risks related to the uncertain global economic environment; and other risks and uncertainties related to our prospects,
properties and business strategy, as described in more detail in Plateau Uranium's recent securities filings available at www.sedar.com. Actual events or results may differ materially from those projected in
the forward-looking statements and Plateau Uranium cautions against placing undue reliance thereon. Neither Plateau Uranium nor
its management assume any obligation to revise or update these forward-looking statements.
Neither TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in the policies of the TSX
Venture Exchange) accepts responsibility for the adequacy or accuracy of this release.