Further High-Grade Copper and Gold Mineralisation Identified at Chanach

Criteria

JORC Code Explanation

Commentary

Sampling Techniques

• Nature andquality of sampling (e.g. cut channels, random chips, or specific specialised industry standard measurement tools appropriate to the minerals under investigation, such as down hole gamma sondes,or handheld XRF instruments, etc.). These examples should not be taken as limiting the broad meaning of sampling
• Include reference to measures takento ensure sample representivity and the appropriate calibration of any measurement tools or systems used.
• Aspects of the determination of mineralisation that are Material to the Public Report.
• In cases where ‘industry standard' work has been done this would be relatively simple (e.g. ‘reverse circulation drilling was used to obtain 1 m samples from which 3 kg was pulverised to produce a 30 g charge for fire assay'). In other cases more explanation may be required, such as wherethere is coarse gold that has inherent sampling problems. Unusual commodities or mineralisation types (e.g. submarine nodules) may warrant disclosure of detailed information.

• Sample bags were visually inspected for volume to ensure minimal size variation. Sampling was carried out understandard industry protocols and QAQC procedures.
• A 50-gram sample is digested for gold analysis by Fire Assay and Atomic Adsorption Spectrophotometry (AAS), andfor copper analysis via pressed pellet X-ray florescence (XRF).
• A 0.2-gram sampleis digested formulti-element analysis by Fire Assay and Inductive Coupled Plasma (ICP)using Mass Spectroscopy (MS) or Optical Emission Spectroscopy (OES).
• The trench samples in 2023 wereundertaken by an experienced geologist who determined from mapping of bedrock and trenches the areas to be sampled.
• All samples were dried and crushed to 90% passing 2mm. A 300g split was taken and pulverised to 80% passing 74 microns. The samples wereanalysed using AtomicAbsorption.

Drilling Techniques

• Drill type (e.g. core, reverse circulation, open-hole hammer, rotary air blast, auger, Bangka, sonic, etc.) and details (e.g. core diameter, triple or standard tube, depth of diamond tails, face- sampling bit or other type,whether core is oriented and if so, by what method, etc.).

• N/A

Drill sample recovery

• Method of recording and assessing core and chipsample recoveries and results assessed.
• Measures takento maximise sample recovery and ensure representative nature of the samples.
• Whether a relationship exists between sample recovery and grade and whether sample bias may have occurred due to preferential loss/gain of fine/coarse material.

• N/A

Logging

• Whether coreand chip sampleshave been geologically and geotechnically logged to a level of detail to support appropriate Mineral Resource estimation, mining studies and metallurgical studies.
• Whether loggingis qualitative or

• Logging is considered qualitative.
• All 2023 trenchgrab samples werelogged and recorded on primary documents and maps.

Criteria

JORC Code Explanation

Commentary

quantitative in nature.Core (or costean, channel, etc.) photography.

• The total length and percentage of the relevant intersections logged.

Sub-sampling techniques and sample preparation

• If core, whether cut or sawn and whether quarter, half or all core taken.
• If non-core, whether riffled, tube sampled, rotary split,etc and whether sampled wet or dry.
• For all sample types,the nature, quality and appropriateness of the sample preparation technique.
• Quality control procedures adopted for all sub-sampling stages to maximise representivity of samples.
• Measures taken to ensure that the sampling is representative of the in situ material collected, including for instance results for field duplicate/second-half sampling.
• Whether samplesizes are appropriate to the grain size of the material being sampled.

• At this stageof the exploration no sub sampling is undertaken during the collection stage.
• The sample sizesare considered to be appropriate to correctly represent the mineralisation style.

Quality of assay data and laboratory tests

• The nature, quality and appropriateness of the assaying and laboratory procedures used and whether the technique is considered partial or total.
• For geophysical tools, spectrometers, handheld XRF instruments, etc., the parameters used in determining the analysis including instrument make and model, reading times, calibrations factors applied and their derivation, etc.
• Nature of quality control procedures adopted (e.g. standards, blanks, duplicates, external laboratory checks) and whether acceptable levels of accuracy (i.e. lack of bias) and precision have been established.

• The analytical techniques Fire Assay, Atomic adsorption Spectrophotometry for gold analysis and ICP MS or OES for multi-element analysis are considered suitable for the reconnaissance style sampling undertaken.
• Gold analysis wascarried out usingFire Assay with finishing on a Thermo Scientific Solar S2 AA- Spectrometer.
• Multi-element analysis was carried out by aqua regia digestwith ICP MS and OESanalysis using an iCAP 6300 ICP-instrument manufactured by Thermo-Scientific.
• Laboratory QAQC involves the use of internal lab standards using certified reference material, blanks, splits and replicates as part of the in-house procedures.
• All samples from the 2023 trench sampling program were analysed at Information and Research Centre Laboratory, which has all international standards certification and were subject to in-house QAQC procedures.

Verification of sampling and assaying

• The verification of significant intersections by eitherindependent or alternative company personnel.
• The use of twinned holes.
• Documentation of primary data, data entry procedures, data verification, data storage (physical and electronic) protocols.
• Discuss any adjustment to assay data.

• An executive director of Chanach LLC has visually verified significant intersections in rock samples from the Chanach project.
• N/A
• Primary data was collected usinga set of standard Excel templates on paper and re-entered into laptop computers. Assay data is received in digital and hard copy directly from the laboratory and imported into the database.
• No adjustments or calibrations weremade to any assay data used in this report.

Criteria

JORC Code Explanation

Commentary

Location of data points

• Accuracy and quality of surveys used to locate drill holes (collar and down- hole surveys), trenches, mine workings and other locations used in Mineral Resource estimation.
• Specification of the grid system used.
• Quality andadequacy of topographic control.

• Sample locations were recorded using handheld Garmin GPS60s.Elevation values were in AHDRL and values recorded within the database. Expected accuracy is + or - 3 to 7 m for easting, northing and 10m for elevation coordinates.
• The grid systemis WGS84 UTM (zone42 north).
• Topographic surface uses handheld GPS elevation data, which is adequate at the current stage of the project.
• Location of the 2023 trenchsamples were recorded using a handheld Garmin GPS.

Data spacing and distribution

• Data spacing for reporting of Exploration Results.
• Whether the data spacing and distribution is sufficient to establish the degree of geological and grade continuity appropriate for the Mineral Resource and Ore Reserve estimation procedure(s) and classifications applied.
• Whether samplecompositing has been applied.

• N/A
• N/A
• The 2023 trench samples were composited in meter intervals across the trenches dug. 3 to 4 kg samples were taken from each meter width.

Orientation of data in relation to geological structure

• Whether the orientation of sampling achieves unbiased sampling of possible structures and theextent to which this is known, considering the deposit type.
• If the relationship between the drilling orientation and the orientation of key mineralised structures is considered to have introduced a sampling bias, this should be assessed and reported if material.

• N/A
• N/A

Sample security

• The measures taken to ensure sample security.

• Sample security is managed by Chanach LLC. Samples are collected by Company employees and transported by Company vehicles to theLaboratory in Kara Balta. The sample processing facility has Security Officers on duty 24 hours per day. The Company stores all mineralised intervals and all laboratory samples in a secured steel vault within the secured processing facility.
• The 2023 sample security was managed by Site management. Samples are collected by Company employees and transported by Company vehicles to the Laboratory in Kara Balta. The processing facility has security officers on duty 24 hours per day. The Company stores all mineralised intervals and laboratory samples in the secured sample store.

Audits or reviews

• The results of any audits or reviews of sampling techniques and data.

• The Company carriesout its own internal data audits. No problems have been detected.

Criteria

JORC Code Explanation

Commentary

Mineral tenement and land tenure status

• Type, reference name/number, location and ownership including agreements or material issues with third parties such as joint ventures, partnerships, overriding royalties, native title interests, historical sites, wilderness or national park and environmental settings.
• The security of the tenure held at the time of reporting along with any known impediments to obtaining a licence to operate in the area.

• The mineralisation is located within Exploration License AP6771which is a Joint Venture between RTG Mining Inc (90%) and BW3 Pty Ltd (10%)
• There are no othermaterial issues.
• The tenement is in goodstanding and no known impediments exist.

Exploration done by other parties

• Acknowledgment and appraisal of exploration by other parties.

• No other exploration has been carried out

Geology

• Deposit type,geological setting and style of mineralisation.

• The geological setting is of Cambrian to Permian aged intrusive porphyry systems, bounded by overlying basaltic, and sedimentary rocks. Mineralisation is mostly situated within granitic porphyry unitsas broad alteration containing copper sulphides and withinnarrow quartz veinsand faults.

Skarn mineralisation consists of magnetite, pyrite, chalcopyrite,malachite, azurite, limonite, haematite, epidote and granular andradite.

Drill Hole Information

• A summary of all information material to the understanding of the exploration results including a tabulation of the following information for all Material drill holes:

o easting and northing of the drillhole collar

o elevation or RL (Reduced Level - elevation above sea levelin meters) of the drill hole collar

o dip and azimuth of the hole

o down hole lengthand interception depth

o hole length.

• If the exclusion of this information is justified on the basis that the information is not Material and this exclusion does not detract from the understanding of the report, the Competent Person should clearly explain why this is the case.

• N/A

Data Aggregation methods

• In reporting Exploration Results, weighting averaging techniques, maximum and/or minimum grade truncations (eg cutting of high grades) and cut-off grades are usually Material and should be stated.
• Where aggregate intercepts incorporate short lengthsof high grade results and longer lengthsof low grade

results, the procedure used for such aggregation should be stated and some

• No length weighting has been applieddue to the nature of the sampling technique.
• No top-cuts have been applied in reporting of the intersections.
• No aggregate intercepts areused.
• No metal equivalent values are usedfor reporting exploration results.

Criteria

JORC Code Explanation

Commentary

typical examples of such aggregations should be shown in detail.

• The assumptions used for any reporting of metalequivalent values should be clearly stated.

Relationship between mineralisation widths and intercept lengths

• These relationships are particularly important in the reporting of Exploration Results.
• If the geometry of the mineralisation with respect to the drill hole angle is known, its nature shouldbe reported. If it is not known and only the down hole lengths are reported, there should be a clear statement to this effect (e.g. ‘down hole length, true width not known').

• The 2023 trenchsamples were takenfrom meter length samples taken at right angles across the mapped vein and represent true widths of the mineralisation.

Diagrams

• Appropriate maps and sections (with scales) and tabulations of intercepts should be included for any significant discovery being reported These should include, but not be limited to a plan view of drill hole collar locations and appropriate sectional views.

• Appropriate maps and sections are included in previous announcements.
• Photos and regional map showing mapping locations and trenches for the 2023program are included in this update.

Balanced Reporting

• Where comprehensive reporting of all Exploration Results is not practicable, representative reporting of both low and high gradesand/or widths should be practiced to avoid misleading reporting of Exploration Results.

• Representative reporting is included withinthe body of this report and in previous announcements.

Other substantive exploration data

• Other exploration data, if meaningful and material, should be reported including (but not limited to): geological observations; geophysical survey results; geochemical survey results; bulk samples - size and method of treatment; metallurgical test results; bulk density, groundwater, geotechnical and rock characteristics; potential deleterious or contaminating substances.

• Exploration targeting has been enhanced by a structural study completed by Orefind in 2017, a ground magnetics study by Southern Geoscience in 2016 and a geophysical study completed by Baoding Geological Engineering Institute in 2011. The project is a target rich environment with 2019 planned exploration focussing on multiple targets. This has been further enhanced by a structural survey completed by Vaulin in 2022.
• No metallurgical test workhas been conducted on the 2023 sampling.

Further Work

• The nature and scaleof planned further work (e.g. tests for lateral extensions or depth extensions or large-scale step- out drilling). Diagrams clearly highlighting the areas of possible extensions, including the main geological interpretations and future drilling areas, provided this information is not commercially sensitive.

• Ongoing reverse circulation and diamond drilling will be used to further define the nature and extent of the geochemical anomalism, and to gain lithological information.
• Most mineralisation is open bothalong strike and down dip.
• Further structural mapping, geophysical interpretation, trenching and drilling will be required to develop the resource model following the 2023 sampling regime.